防護手套CE認證EN420標準

防護手套出口到歐盟銷售是要做EN420標準測試的，下面小編就簡單介紹一下EN420標準一般要求和測試方法等內容，大家可以做一個參考。

EN 420: 2003 + A1: 2009

Protective gloves. General requirements and test methods

EN 4202003 + A12009

防護手套EN420標準一般要求和測試方法

This standard is designed to ensure that the gloves themselves do not cause harm to the wearer and are comfortable to wear. Tests and requirements include the pH and chrome VI content of leather plus water vapour transmission and absorption of materials. Also procedures to examine the sizing of the glove and its effect on finger dexterity are covered plus general requirements for the information to be supplied with and marked on the glove.

?

該標準旨在確保手套本身不會對佩戴者造成傷害，而且佩戴舒適。測試和要求包括皮革的pH和六價鉻含量，以及材料的水汽傳輸和吸收性能。此外，還包括檢查手套尺寸及其對手指靈活性的影響，以及手套標示和隨附信息的一般要求。

?

Length 長度?

The length of the glove is measured by suspending it from the middle finger with a graduated rule having a rounded tip designed to fit the tip of the finger. The glove is manipulated to remove any wrinkles or ??folds and the minimum length is recorded. EN 420 includes a list of minimum lengths for each glove size, however, gloves for special purpose are permitted to be below the minimum length but in such situations the manufacturer must demonstrate that they are fit for special purpose by a statement in the user instructions.

?

專門用于測量手套長度的量尺為圓柱形，一端為圓形，以配合手套指尖的形狀。將手套中指套在量尺上垂直懸掛，可以測得其長度。測量時，要整理手套，不得有任何皺紋或折疊，記錄*小長度。EN 420中列出了每種手套尺碼的*小長度，不過，對于特殊用途的手套，允許低于*小長度，但在這種情況下，制造商必須在使用說明書中聲明它們的特殊用途。

?

Sizing / Dexterity 尺碼/ 靈巧性

Gloves are fitted on a hand of the size that they are intended to fit and comments are made regarding comfort and fit. The wearer will then try to pick up pins of varying size to provide an indication of dexterity. Five pins are defined of diameter from 5 mm to 11mm, clearly the smaller the diameter that can be picked up the greater the dexterity result.

?

將手套佩戴在對應尺碼的手上，對舒適性和貼合性做出評論。然后佩戴者將嘗試拾取不同尺寸的金屬小圓柱，了解其靈巧性。小圓柱的直徑分布為5mm到11mm，顯然，可以拾取的圓柱直徑越小，靈巧性結果越也越好。

pH Value pH值

The determination of pH value of both leathers and textiles on a glove is required. This pH value shall be greater than 3.5 and less than 9.5. The test samples are taken from the palm of the glove, if other part of the glove contains different material, these materials shall be tested separately. A prepared test sample is extracted in water by mechanical shaking; the aqueous extract is then decanted and the pH value determined by a pH meter. An excessive amount of acid or ??alkali in a material has been linked to skin dermatitis and may indicate poor process control.

?

要求測定手套上皮革和紡織品的pH值，應大于3.5且小于9.5。從手套的手掌部位取樣，如果手套的其他部位含有不同的材料，則應分別測試。通過機械搖動將制備的測試樣品在水中進行提取，然后將水提取物倒出來，用pH計測定pH值。如果材料中酸或堿過量，會引起皮炎，可能表明制程控制不良。

?

Chrome VI 六價鉻

Each type of leather on a glove shall be tested separately and comply with the requirement of less than 3mg/kg of chromium VI. Two samples require testing from each leather type; these two samples shall be taken from different gloves. The soluble chromium VI is leached from the leather in a phosphate buffer. The chromium VI in the extract is then oxidized to produce a red/violet colour; this can then be quantified by a UV spectrophotometer. Chromium VI is a restricted substance as well as being a known allergen.

?

手套上的每種皮革應單獨測試并符合六價鉻低于3mg / kg的要求。每種皮革要測試兩個樣品，并分別從不同的手套上取樣。在磷酸鹽緩沖液中，可溶性六價鉻會從皮革中濾出。提取物中的六價鉻會氧化，呈紅/紫色; 然后可以通過UV分光光度計測定其含量。六價鉻是已知的過敏原，也是限用物質。

以上就是小編介紹的防護手套

CE認證EN420標準的一般要求和測試方法，如果您有產品辦理CE認證可以直接聯系我們